Part #RWBK5570 STEPS: READ THESE INSTRUCTIONS CAREFULLY! IMPORTANT: THE ORIGINAL WHEELS MAY NOT FIT. PLEASE MAKE SURE TO CHECK WHEELS BEFORE ASSEMBLY, THIS WAY YOU WONT BE DISAPPOINTED IF THEY DO NOT FIT. Jack rear of vehicle and support the axle with jack stands. Remove the wheels, brake drums, axles and backing plate assembly. Clean more…
Archive for April, 2009
GM 10-12 Bolt, 5 X 4.75” Rear Disc Brake Kit #RWBK-1012
Part #RWBK-1012 STEPS: READ THESE INSTRUCTIONS CAREFULLY! IMPORTANT: THE ORIGINAL WHEELS MAY NOT FIT. PLEASE MAKE SURE TO CHECK WHEELS BEFORE ASSEMBLY, THIS WAY YOU WONT BE DISAPPOINTED IF THEY DO NOT FIT. Jack rear of vehicle and support the axle with jack stands. Remove the wheels, brake more…
55-57 Chevy Belair, Transmission Crossmember Kit
Part #TCM5557DP Disconnect battery ground cable when applies. Remove any fluid lines, wiring, cables, or any flammable materials in the areas where welding will be performed. Use a piece of sheet steel or aluminum between frame and floorboard to protect carpeting also. Remove carpet and padding where possible. Install rubber trans mount and crossmember with 7/16” more…
55-57 Belair, Universal Square Tube Transmission Crossmember
Part #TCM5557 READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING THIS CONVERSION: MAKE SURE THIS KIT FITS YOUR APPLICATION BEFORE PAINTING OR PLATING. PARTS THAT HAVE BEEN PAINTED. PLATED OR MODIFIED MAY NOT BE RETURNED. Determine the proper installation location for the crossmember by mounting the engine and transmission and centering the transmission between the frame rails. The more…
Throttle Cable Bracket
• Manual or Automatic Transmission • Fully adjustable • Throttle return spring mounting hole • Fits most 2 or 4 bbl carburetors Tighten bolt to steady bracket. For 700R4 transmissions use Kickdown Adapter Bracket P/N 2429.
Truck Rear Axle Kits
Your leading source for Chassis! 47-55 Chevy Truck, Rear Axle Relocation Kit Converting the 47-55 Chevy trucks from an enclosed drive shaft rear end to the modern open drive shaft rear end always posed the problem of the rear end not being centered in the wheel well. This would happen because the spring center bolt more…
Vacuum Pump Detail
A – Vacuum hose B – *Check valve connects manifold to port on vacuum pump C – Optional Muffler D – Intake port E – Exhaust port F – Ground wire G – Positive wire (connect to vacuum switch) H – Optional mounting hardware I – Bolts and washers J – Insulation washers K – more…
65-68 Chevy full size GM car (Lg. caliper), w/ 3/4” spindle nuts, Disc brake wheel kit
Part #(WBKS6568A) Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. This Conversion Kit uses the following components: Rotors 69-72 chevelle more…
65-68 Chevy full size car (Sm. caliper), Stock spindle disc brake kit
Part #WBKS6568 Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. 1. Jack front of vehicle and support it properly with jack more…
57-64 Ford 1/2 ton pickup, 5 1/2” bolt circle, Disc brake conversion kit
Part #WBKS5764 Read these instructions completely before installing this kit!!! NOTE: Before beginning installation, TAKE THE FRONT WHEELS THAT YOU ARE GOING TO USE AND MAKE SURE THAT THEY FIT THE ROTOR BOLT PATTERN, AND THAT THEY HAVE A LARGE ENOUGH CENTER HOLE. THESE ARE 11 3/4” ROTORS SO YOU’LL NEED 15” WHEELS. Note also more…
55-64 Chevy full size car, Stock spindle disc brake kit (Lg. GM calipers)
Part #(WBKS5564A) Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. This Conversion Kit uses the following components: Rotors 69-72 chevelle more…
37-48 Ford passenger car & 37-56 Ford 1/2 ton pickup, 5 1/2” bolt circle, Disc brake wheel kit
Read these instructions completely before installing this kit!!! NOTE: Before beginning installation, TAKE THE FRONT WHEELS THAT YOU ARE GOING TO USE AND MAKE SURE THAT THEY FIT THE ROTOR BOLT PATTERN, AND THAT THEY HAVE A LARGE ENOUGH CENTER HOLE. THESE ARE 11 3/4” ROTORS SO YOU’LL NEED 15” WHEELS. Make sure this kit more…
49-59 Chevy/GMC truck, 6 x 5.5 Disc brake kit
Part #WBK6-4959 Steps: Read these instructions carefully! IMPORTANT: THIS KIT CONTAINS 12” ROTORS, THE ORIGINAL WHEELS MAY NOT FIT. PLEASE MAKE SURE TO CHECK WHEELS BEFORE ASSEMBLY, THIS WAY YOU WON’T BE DISAPPOINTED IF THEY DO NOT FIT. Jack front of truck and support the axle with jack stands. Remove the wheels, brake drums, hub more…
55-64 Chevy Fullsize car (Sm. caliper), Stock spindle Disc brake wheel kit
Part #WBKS5564 Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. 1. Jack front of vehicle and support it properly with jack more…
49-54 Chevy Car/53-62 Chevy Corvette, Disc brake conversion kit (Lg. caliper)
Part #WBKS4954 and #WBKS5362 Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. This Conversion Kit uses the following General Motors more…
49-53 Ford & 52-53 Mercury car, Disc brake conversion kit, 4.5 bolt pattern
Part # (WBKS4953) Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. This Conversion Kit uses the following rotors and seals: more…
60-70 Chevy Truck, Disc Brake Conversion Kit, 4.75 bolt pattern
See our extensive collection of Chevy C10 disc brake conversion kits and parts For Part #‘s (WBK5-6062 & WBK5-6370) Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have more…
49-51 Mercury car, Disc brake conversion kit, 5.5 bolt pattern
Read these instructions completely before installing this kit!!! Before beginning installation, make sure your wheels fit on the disc rotor. Make sure this kit fits your application before painting or plating. Parts that have been painted, plated or modified may not be returned. This Conversion Kit uses the following rotors and calipers: ROTORS: 94-06 Ford more…
1955-64 Chevy Fullsize, Disc Brake Conversion Bracket Kit (Lg. GM Caliper)
1955-58 FULL-SIZE CHEVY CAR 1959-64 FULL-SIZE CHEVY CAR Part #(DB5564A) CHECKLIST: • 5/8-18” x 1” Bolt • 5/8-18” x 1 1/4” Bolt • 7/16-20” x 2 3/4” Bolts • 7/16-20” x 2 1/2” Bolts • 1/2-20” x 2 1/2” Bolts • 7/16-20” Nylox Nuts • 1/2-20” Nylox Nuts • 5/8” ID x 3/8” Thick Spacers more…
800-638-1703
